• socket converter
• calibration test POD - ISP dagnose POD - accessories

 Back to top

Features

GENERAL

• PIKprog2 is the member of the new generation of Windows 98/ME/NT/2000/XP/2003/XPx64/Vista based ELNEC specialized programmers. Programmer is capable to support all currently available Microchip^TM PICmicro^® series microcontrollers (8-40 pins) using parallel and serial algorithms. The PIKprog2 programmer isn't development grade programmer, but meets all Microchip's requirements to manufacturing grade of programmers. The PIKprog2 has been developed in close cooperation with Microchip^TM company, therefore programmer's hardware is focused to support all current and future PICmicro^® family microcontrollers.
• PIKprog2 is a small, very fast and powerful portable programmer for PICmicro^® family microcontrollers and serial EEPROM with IIC (24Cxx), Microwire (93Cxx) and SPI (25Cxx) interface types. Using build-in in-circuit serial programming (ISP) connector programmer is able to program PICmicro^® family microcontrollers using serial algorithms.
• Provides very competitive price with excellent hardware design for reliable programming. Nice "value for money" in this class.
• Very fast programming due to high-speed FPGA driven hardware and support of high-speed USB port. Surely faster than competitors in this category.
• PIKprog2 interfaces with the IBM PC compatible, portable or desktop personal computers through USB port.
• PIKprog2 is easy upgradeable to SmartProg2 programmer using "Xprog2 to SmartProg2 upgrade kit" (ord.no. 60-0048).

 Back to top

HARDWARE

• 40 powerful TTL pindrivers provide H/L/pull_up/pull_down and read capability for each pin of socket. Advanced pindrivers incorporate high-quality high-speed circuitry to deliver signals without overshoot or ground bounce for all supported devices. Pin drivers operate down to 1.8V so you'll be ready to program the full range of today's advanced low-voltage devices.
• The programmer performs device insertion test (wrong device position in socket) and contact check (poor contact pin-to-socket) before it programs each device. These capabilities, supported by signature-byte check help prevent chip damage due to operator error.
• PIKprog2 programmer performs programming verification at the marginal level of supply voltage, which, obviously, improves programming yield, and guarantees long data retention.
• Various socket converters are available to handle device in PLCC, SOIC, SSOP, TSSOP, TQFP and other packages.

 Back to top

SOFTWARE

• Programmer is driven by an easy-to-use control program with pull-down menus, hot keys and on-line help. Selecting of device is performed by its class, by manufacturer or simply by typing a fragment of vendor name and/or part number.
• Standard device-related commands (read, blank check, program, verify, erase) are enhanced by some test functions (insertion test, signature-byte check), and some special functions (autoincrement).
• The rich-featured autoincrement function enables one to assign individual serial numbers to each programmed device - or simply increments a serial number, or the function enables one to read serial numbers or any programmed device identification signatures from a file.
• The software also provide a many information about programmed device. As a special, the drawing of all available packages are provided. The software provide also explanation of chip labelling (the meaning of prefixes and suffixes at the chips) for each supported chip.
• The software provide a full information for ISP implementation: Description of ISP connector pins for currently selected chip, recommended target design around in-circuit programmed chip and other necessary information.

 Back to top

CARE FOR THE CUSTOMERS

• It is important to remember that support of new devices with compatible GND/VCC/VPP pinout requires only a software update due to the PIKprog2 hardware. With our prompt service you can have a new device added to the list of supported devices within hours! Free software updates are available by download from our WEB site.
• Keep-Current and AlgOR services, our next step to be customers satisfied.
  • Keep-Current service means, that ELNEC send off the latest version of programmer software and updated user documentation (Keep-Current package) to customer. A Keep-Current service is your hassle-free guarantee that you are doing the highest quality programming on ELNEC programmers, at minimal cost.
  • AlgOR (Algorithm On Request) service gives to the user tool to influence to amount and types of programmed devices as needed.

 Back to top

Specification

HARDWARE

Programmer

• two D/A converters for VCCP and VPP, controllable rise and fall time
• VCCP range 2..7V/350mA
• VPP range 2..25V/200mA
• USB 2.0/1.1 compatible interface
• autocalibration
• selftest capability

ZIF socket, pindriver

• 40-pin DIL ZIF (Zero Insertion Force) socket accepts both 300/600 mil devices up to 40-pins
• pindriver: 40 TTL pindrivers, special GND/VCC/VPP pindriver for PICmicro^® devices
• spare GND, VCC and VPP driver, which add additional made-by-wire GND/VCC/VPP pin capability for future devices
• FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on all pindriver pins, level H selectable from 1.8 V up to 5V
• continuity test: each pin is tested before every programming operation

ISP connector

• 10-pin male type with missinsertion lock
• 6 TTL pindrivers, provides H, L, CLK, pull-up, pull-down; level H selectable from 1.8V up to 5V to handle all (low-voltage including) devices.
• 1x VCCP voltage (range 2V..7V/100mA) (*1) and 1x VPP voltage (range 2V..25V/50mA)
• programmed chip voltage (VCCP) with both source/sink capability and voltage sense
• ISP diagnostic POD

• (*1) - the programmer is not capable to supply a target system from VCCP pin. If you have such demand, use please a BeeProg programmer

DEVICE SUPPORT

Programmer, in ZIF socket

• microcontrollers Microchip^TM PICmicro^®: PIC10xxx, PIC12xxx, PIC14xxx, PIC16xxx, PIC17xxx, PIC18xxx, dsPIC series, 8 to 40 pins (*1)
• Serial E(E)PROM: 17Cxxx, 24Cxxx, 24Fxxx, 25Cxxx, 59Cxxx, 85xxx, 93Cxxx series

• (*1) - suitable adapters are available for non-DIL packages and devices with more than 40 pins.

Programmer, through ISP connector

• Microcontrollers Microchip PICmicro: PIC10xxx, PIC12xxx, PIC16xxx, PIC17xxx, PIC18xxx, dsPIC series

Identification of manufacturer with Logos

Programming speed

 Back to top

SOFTWARE

• Algorithms: only manufacturer approved or certified algorithms are used. Custom algorithms are available at additional cost.
• Algorithm updates: software updates are available approx. every 2 weeks, free of charge.
• Main features: revision history, session logging, on-line help, device and algorithm information.

Device operations

• standard:
  • intelligent device selection by device type, manufacturer or typed fragment of part name
  • blank check, read, verify
  • program
  • erase
  • configuration and security bit program
  • illegal bit test
  • checksum
• security
  • insertion test
  • contact check
  • ID byte check
• special
  • auto device serial number increment
  • statistic
  • count-down mode

Buffer operations

• view/edit, find/replace
• fill, copy, move, byte swap, word/dword split
• checksum (byte, word)
• print

File load/save

• no download time because programmer is PC controlled
• automatic file type identification
  Supported file formats
  • unformatted (raw) binary
  • HEX: Intel, Intel EXT, Motorola S-record, MOS, Exormax, Tektronix, ASCII-SPACE-HEX

 Back to top

GENERAL

PC system requirements

• Common, software related requirements
• Programmer hardware related requirements:
  • one USB port

Operation

• operating voltage 15..20V DC, max. 0.5A
• dimensions 160x95x35 mm (6.3x3.7x1.4 inch)
• weight (without external power adapter) ca. 500g (17.65 oz)
• temperature 5°C ÷ 40°C (41°F ÷ 104°F)
• humidity 20%..80%, non condensing

Base configuration package includes

• PIKprog2 programmer
• wall plug adapter, 12V DC/500mA, unstabilized
• connection cable PC-programmer
• ISP cable
• diagnostic POD for selftest
• anti-dust cover for ZIF socket
• user manual
• software
• registration card
• transport case

Additional services

• Keep-Current - ELNEC sends to user a latest version of programmer software and updated user documentation (Keep-Current package).
• AlgOR - new supported devices on customer request
•  

Programmer price also includes

• free technical support (hot line)
• free life-time software update via Internet